Supported Storage List for LifeKeeper for Linux v9
Last updated: May 25, 2021
The table below is a list of LifeKeeper for Linux v9 supported storage and should be considered when configuring your environment.
About Supported Storage
Some types of storage used as shared storage in LifeKeeper require certification.
The following storage must be certified. Make sure the storage you plan to use is listed in the table below. Supported storage should be used for shared storage such as SCSI/FC/iSCSI/SAS that refer to the same data from multiple nodes for which LifeKeeper’s IO fencing with SCSI-2/3 Reservation is required.
Configurations that do not require certification
- NAS storage (requires the NAS Recovery Kit)
- All disk devices that make up data replication by DataKeeper (both built-in and external)
- Virtual disks on shared storage protected by the VMDK Recovery Kit on vSphere
- Storage which is used in the environment where all of the requirements below are satisfied:
- OS, hardware and platform has supported the storage
- The LifeKeeper SCSI reservation feature is disabled
- The fencing mechanism of LifeKeeper Quorum/Witness is configured
Note: If your shared storage meets the requirements above, it does not require SIOS certification.
Unsupported Hardware
Consumer storage that is connected via USB or IEEE1394 is not supported.
DELL
Vendor (*1) |
Storage Model | Bus Type | Connect Type (*2) |
Support Status | Required ARK (i.e. Multipath ARK) |
Supported LK Version (*4) | Notes |
---|---|---|---|---|---|---|---|
DELL | Dell EqualLogic: PS4100 PS4110 PS4210 PS6100 PS6110 PS6210 PS6610 |
ISCSI | Multi Path (DMMP) | YES | DMMP ARK | v9.0 – v9.5.2 | With a large number of luns (over 20), change the REMOTETIMEOUT setting in /etc/default/LifeKeeper to REMOTETIMEOUT=600. |
Single Path (DMMP) | YES | DMMP ARK | |||||
MD3800f MD3820f MD3860f |
FC | vSphere (RDM) | No | – | v9.0 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
MD3400 MD3420 MD3460 |
SAS | vSphere (RDM) | No | – | v9.0 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
SCv3000 Series: SCv3000 SCv3020 |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | YES | DMMP ARK | v9.0 – v9.5.2 | |||
Single Path | No | – | |||||
SAS | vSphere | No | – | v9.0 – v9.5.2 | |||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
SCv2000 Series: SCv2000 SCv2020 SCv2080 |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | YES | DMMP ARK | v9.0 – v9.5.2 | |||
Single Path | No | – | |||||
SAS | vSphere | No | – | v9.0 – v9.5.2 | |||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
Dell Storage: SC7020 SC5020 SC4020 |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | YES | DMMP ARK | v9.0 – v9.5.2 | |||
Single Path | No | – | |||||
Dell Compellent: SC9000 SC8000 |
FC | vSphere (RDM) | No | – | – | ||
Multi Path (DMMP) | No | – | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | YES | DMMP ARK | v9.0 – v9.5.2 | |||
Single Path | No | – |
Fujitsu
Vendor (*1) |
Storage Model |
Bus Type | Connect Type (*2) |
Support Status |
Required ARK (i.e. Multipath ARK) |
Supported LK Version (*4) |
Notes |
---|---|---|---|---|---|---|---|
Fujitsu | ETERNUS: DX60 S2 DX80 S2 DX90 S2 DX410 S2 DX440 S2 DX8100 S2 DX8700 S2 DX60 S3 DX100 S3 DX200 S3 DX500 S3 DX600 S3 DX8700 S3 DX8900 S3 DX200F DX60 S4 DX100 S4 DX200 S4 DX500 S4 DX600 S4 DX60 S5 DX100 S5 DX200 S5 DX500 S5 DX600 S5 DX900 S5 AF250 AF650 AF250 S2 AF650 S2 AF250 S3 AF650 S3 DX8900 S4 |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | If ETERNUS is used as a boot device, a file system error may occur when the boot device is not accessible from a primary node and switching to a secondary node may fail. In order to avoid this, set a panic when a file system error occurs as shown below. Example: for xfs, configure the following and reboot the server. echo ‘fs.xfs.panic_mask=127’ > /etc/sysctl.d/01-xfs.conf |
Multi Path (DMMP) | YES | DMMP ARK | |||||
Multi Path (EMPD) | YES | No Multipath ARK | |||||
Single Path | YES | No Multipath ARK | |||||
ISCSI | Multi Path (DMMP) | YES | DMMP ARK | v9.0 – v9.5.2 | |||
Multi Path (EMPD) | YES | No Multipath ARK | |||||
Single Path | YES | No Multipath ARK |
Hitachi / Hitachi Vantara
Vendor (*1) |
Storage Model |
Bus Type | Connect Type (*2) |
Support Status |
Required ARK (i.e. Multipath ARK) |
Supported LK Version (*4) |
---|---|---|---|---|---|---|
Hitachi / Hitachi Vantara | Hitachi Virtual Storage Platform G1000 Hitachi Virtual Storage Platform G1500 Hitachi Virtual Storage Platform F1500 |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 |
Multi Path (HDLM) | YES | HDLM ARK | ||||
Multi Path (DMMP) | YES | DMMP ARK | ||||
Single Path | YES | – | ||||
ISCSI | Multi Path (HDLM) | No | – | – | ||
Single Path | No | – | ||||
Hitachi Virtual Storage Platform | FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | |
Multi Path (HDLM) | YES | HDLM ARK | ||||
Single Path | YES | – | ||||
ISCSI | Multi Path (HDLM) | No | – | – | ||
Single Path | No | – | ||||
Hitachi Virtual Storage Platform Mid Range Family: Hitachi Virtual Storage Platform F900 (VSP F900) Hitachi Virtual Storage Platform F700 (VSP F700) Hitachi Virtual Storage Platform F370 (VSP F370) Hitachi Virtual Storage Platform F350 (VSP F350) Hitachi Virtual Storage Platform G900 (VSP G900) Hitachi Virtual Storage Platform G700 (VSP G700) Hitachi Virtual Storage Platform G370 (VSP G370) Hitachi Virtual Storage Platform G350 (VSP G350) Hitachi Virtual Storage Platform G150 (VSP G150) Hitachi Virtual Storage Platform G130 (VSP G130) |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | |
Multi Path (HDLM) | YES | HDLM ARK | ||||
Multi Path (DMMP) | YES | DMMP ARK | ||||
Single Path | YES | No Multipath ARK | ||||
ISCSI | Multi Path (DMMP) | YES | DMMP ARK | v9.0 – v9.5.2 | ||
Single Path | YES | No Multipath ARK | ||||
Hitachi Virtual Storage Platform Mid Range Family: Hitachi Virtual Storage Platform F800 (VSP F800) Hitachi Virtual Storage Platform F600 (VSP F600) Hitachi Virtual Storage Platform F400 (VSP F400) Hitachi Virtual Storage Platform G800 (VSP G800) Hitachi Virtual Storage Platform G600 (VSP G600) Hitachi Virtual Storage Platform G400 (VSP G400) Hitachi Virtual Storage Platform G200 (VSP G200) Hitachi Virtual Storage Platform G100 (VSP G100) |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | |
Multi Path (HDLM) | YES | HDLM ARK | ||||
Multi Path (DMMP) | YES | DMMP ARK | ||||
Single Path | YES | No Multipath ARK | ||||
ISCSI | Multi Path (DMMP) | YES | DMMP ARK | v9.0 – v9.5.2 | ||
Single Path | YES | No Multipath ARK | ||||
Hitachi Unified Storage VM (HUS VM) | FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | |
Multi Path (HDLM) | YES | HDLM ARK | ||||
Single Path | YES | No Multipath ARK | ||||
ISCSI | Multi Path (HDLM) | No | – | – | ||
Single Path | No | – | ||||
Hitachi Unified Storage 100 Series: Hitachi Unified Storage 150 (HUS 150) Hitachi Unified Storage 130 (HUS 130) Hitachi Unified Storage 110 (HUS 110) |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | |
Multi Path (HDLM) | YES | HDLM ARK | ||||
Single Path | YES | No Multipath ARK | ||||
ISCSI | Multi Path (HDLM) | No | – | – | ||
Single Path | No | – |
Hitachi
Vendor (*1) |
Storage Model |
Bus Type | Connect Type (*2) |
Support Status |
Required ARK (i.e. Multipath ARK) |
Supported LK Version (*4) |
Notes |
---|---|---|---|---|---|---|---|
Hitachi | BR1200 | ISCSI | Multi Path (HDLM) | No | – | – | |
Multi Path (DMMP) | No | – | |||||
Single Path | No | – | |||||
SAS | Multi Path (RDAC) | YES | No Multipath ARK | v9.0 – v9.5.2 | Both the single path and multipath configurations require the RDAC driver. Only the BR1200 configuration using the RDAC driver is supported. The BR1200 configuration using the HDLM (HDLM ARK) is not supported. |
||
Single Path (RDAC) | YES |
No Multipath ARK | |||||
BR1250 | ISCSI | Multi Path (HDLM) | No | – | – | ||
Multi Path (DMMP) | No | – | |||||
Single Path | No | – | |||||
SAS | Multi Path (NECSPS) | YES | NEC SPS ARK | v9.0 – v9.5.2 | Both the single path and multipath configurations require the NEC SPS ARK. The BR1250 configuration using HDLM (HDLM ARK) is not supported. LifeKeeper for Linux v9.1 or later can be used for NEC iStorage StoragePathSavior (NECSPS) Recovery Kit on RHEL7 environment |
||
Single Path (NECSPS) | YES |
NEC SPS ARK | |||||
BR1650E BR 1650S |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | ||
Multi Path (HDLM) | YES | HDLM ARK | |||||
Single Path | YES | – | |||||
ISCSI | Multi Path (HDLM) | No | – | – | |||
Single Path | No | – |
HPE
Vendor (*1) |
Storage Model | Bus Type | Connect Type (*2) |
Support Status | Required ARK (i.e. Multipath ARK) |
Supported LK Version (*4) | Notes |
---|---|---|---|---|---|---|---|
HPE |
Primera A630, A650, A670, C630, C650, C670 | FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | |
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
Nimble Storage: AF20 AF20Q AF40 AF60 AF80 AF1000 AF3000 AF5000 AF7000 AF9000 CS1000H CS1000 CS3000 CS5000 CS7000 HF20C HF20H HF20 HF40 HF60 |
ISCSI | Multi Path (DMMP) | YES | DMMP ARK | v9.2.2 – v9.5.2 | ||
Single Path | No | – | |||||
3PAR: 3PAR StoreServ 8200 3PAR StoreServ 8400 3PAR StoreServ 8440 3PAR StoreServ 8450 |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
3PAR: 3PAR StoreServ 7400 3PAR StoreServ 7400c 3PAR StoreServ 7440 3PAR StoreServ 7440c 3PAR StoreServ 7450 3PAR StoreServ 7450c |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | Note: 3PAR StoreServ 7400 returns a reservation conflict with the default path checker setting. To avoid this conflict, set the following parameter in “/etc/default/LifeKeeper”: DMMP_REGISTRATION_TYPE=hba User friendly device mapping is not supported. Set the following parameter in “multipath.conf” “user_friendly_names no” * When using the vSphere(RDM) for multipath configurations, no configuration parameters need to be set. |
|
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | YES | DMMP ARK | v9.0 – v9.5.2 | Note: 3PAR StoreServ 7400 iSCSI returns a reservation conflict. To avoid this conflict, set the following parameter in “/etc/default/LifeKeeper”: DMMP_REGISTER_IGNORE=TRUE |
||
Single Path | No | – | |||||
3PAR: 3PAR StoreServ 7200 3PAR StoreServ 7200c |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | Note: 3PAR StoreServ 7200 returns a reservation conflict with the default path checker. To avoid this conflict, set the following parameter in “/etc/default/LifeKeeper”: DMMP_REGISTRATION_TYPE=hba |
|
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | No | – | – | |||
Single Path | No | – | |||||
3PAR: 3PAR StoreServ 9450 3PAR StoreServ 20800 R2 3PAR StoreServ 20840 R2 3PAR StoreServ 20850 R2 |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.2.1 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | No | – | – | |||
Single Path | No | – | |||||
3PAR: 3PAR StoreServ 20450 3PAR StoreServ 20800 3PAR StoreServ 20840 3PAR StoreServ 20850 |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.1 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | No | – | – | |||
Single Path | No | – | |||||
3PAR StoreServ 10400 | FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | No | – | – | |||
Single Path | No | – | |||||
3PAR StoreServ 10800 | FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | Note: 3PAR StoreServ 10800 FC returns a reservation conflict with the default path checker setting. To avoid this conflict, set the following parameter in “/etc/default/LifeKeeper”: DMMP_REGISTRATION_TYPE=hba User friendly device mapping is not supported. Set the following parameter in “multipath.conf” “user_friendly_names no” * When using the vSphere(RDM) for multipath configurations, no configuration parameters need to be set. |
|
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | No | – | – | |||
Single Path | No | – | |||||
MSA: MSA2060 |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.1 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | No | – | – | |||
Single Path | No | – | |||||
SAS | vSphere (RDM) | No | – | – | |||
Multi Path (DMMP) | No | – | |||||
Single Path | No | – | |||||
MSA: MSA2050 MSA2052 |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.2 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | YES | DMMP ARK | v9.2 – v9.5.2 | |||
Single Path | No | – | |||||
SAS | vSphere (RDM) | No | – | – | |||
Multi Path (DMMP) | No | – | |||||
Single Path | No | – | |||||
MSA: MSA2042 |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.1 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | YES | DMMP ARK | v9.1 – v9.5.2 | |||
Single Path | No | – | |||||
SAS | vSphere (RDM) | YES | No Multipath ARK | v9.1 – v9.5.2 | |||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
MSA: MSA1040 MSA2040 |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | YES | DMMP ARK | v9.0 – v9.5.2 | |||
Single Path | No | – | |||||
SAS | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | |||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
StoreVirtual (LeftHand) Series LeftHand OS version 12.6 |
FC | vSphere (RDM) | No | – | – | LeftHand OS (SAN/iQ) version 12.6 is supported in HPE StoreVirtual (LeftHand) storage.All StoreVirtual series are supported, including HC250 / HC380 and StoreVirtual VSA as the virtual storage appliance.See the release note of each version of LeftHand OS (SAN/iQ) to know the virtual storage applicance in detail. |
|
Multi Path (DMMP) | No | – | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | YES | DMMP ARK | v9.1 – v9.5.2 | |||
Single Path | No | – | |||||
HP P9500 | FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | YES | No Multipath ARK | |||||
XP7 Storage System | FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | ||
Multi Path (HDLM) | YES | HDLM ARK | |||||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | YES | No Multipath ARK |
IBM
Vendor (*1) |
Storage Model | Bus Type | Connect Type (*2) |
Support Status | Required ARK (i.e. Multipath ARK) |
Supported LK Version (*4) | Notes |
---|---|---|---|---|---|---|---|
IBM | IBM SAN Volume Controller* *IBM TotalStorage Proven | FC | vSphere (RDM) | No | – | v9.0 – v9.5.2 | |
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | YES | No Multipath ARK | |||||
ISCSI | Multi Path (DMMP) | No | – | – | |||
Single Path | No | – | |||||
IBM Storwize V7000 | FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | YES | DMMP ARK Quorum/Witness Server Kit |
v9.0 – v9.5.2 | The IBM Storwize V7000 (Firmware Version 6.3.0.1) has been certified by partner testing using iSCSI (iscsi-initiator-utils6.2.0.872-34.el6.x86_64) with DMMP (device-mapper-1.02.66-6.el6, device-mapper-multipath-0.4.9-46.el6). The test was performed with LifeKeeper for Linux v7.5 using RHEL 6.2. Restriction: IBM Storwize V7000 must be used in combination with the Quorum/Witness Server Kit and STONITH. See the online documentation for the LifeKeeper version that you are using for more information. http://docs.us.sios.com/ |
||
Single Path | No | – | |||||
IBM Storwize V3700 | FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path | No | – | |||||
ISCSI | Multi Path (DMMP) | No | – | – | |||
Single Path | No | – | |||||
SAS | vSphere (RDM) | No | – | – | |||
Multi Path (DMMP) | No | – | |||||
Single Path | No | – | |||||
IBM XIV Storage System | FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | If you are creating more than 32 LUNs on an IBM XIV Storage System using LifeKeeper, please contact IBM for further details. | |
Multi Path (DMMP) | YES | DMMP ARK | |||||
Single Path (DMMP) | YES | DMMP ARK | |||||
ISCSI | Multi Path (DMMP) | No | – | – | |||
Single Path | No | – |
Lenovo
Vendor (*1) |
Storage Model | Bus Type | Connect Type (*2) |
Support Status | Required ARK (i.e. Multipath ARK) |
Supported LK Version (*4) |
---|---|---|---|---|---|---|
Lenovo | Lenovo Storage V3700 V2 Lenovo Storage V3700 V2 XP |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 |
Multi Path (DMMP) | YES | DMMP ARK | ||||
Single Path | No | – | ||||
ISCSI | Multi Path (DMMP) | No | – | – | ||
Single Path | No | – | ||||
SAS | vSphere (RDM) | No | – | – | ||
Multi Path (DMMP) | No | – | ||||
Single Path | No | – | ||||
IBM Storwize V3700 | FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | |
Multi Path (DMMP) | YES | DMMP ARK | ||||
Single Path | No | – | ||||
ISCSI | Multi Path (DMMP) | No | – | – | ||
Single Path | No | – | ||||
SAS | vSphere (RDM) | No | – | – | ||
Multi Path (DMMP) | No | – | ||||
Single Path | No | – |
NEC
Vendor (*1) |
Storage Model | Bus Type | Connect Type (*2) |
Support Status | Required ARK (i.e. Multipath ARK) |
Supported LK Version (*4) | Notes |
---|---|---|---|---|---|---|---|
NEC | NEC iStorage: M10e M11e M100 M110 M300 M12e M120 M320 |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | LifeKeeper for Linux v9.1 or later can be used for NEC iStorage StoragePathSavior (NECSPS) Recovery Kit on RHEL7 environment. |
Multi Path (NECSPS) | YES | NECSPS ARK | |||||
Single Path (NECSPS) | YES | NECSPS ARK | |||||
ISCSI | Multi Path (NECSPS) | YES | NECSPS ARK | v9.0 – v9.5.2 | |||
Single Path (NECSPS) | No | – | |||||
SAS | vSphere (RDM) | No | – | v9.0 – v9.5.2 | |||
Multi Path (NECSPS) | YES | NECSPS ARK | |||||
Single Path (NECSPS) | YES | NECSPS ARK | |||||
NEC iStorage: M310 M310F M320F M500 M510 M700 M710 M710F M520 M720 M720F |
FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 | ||
Multi Path (NECSPS) | YES | NECSPS ARK | |||||
Single Path (NECSPS) | YES | NECSPS ARK | |||||
ISCSI | Multi Path (NECSPS) | YES | NECSPS ARK | v9.0 – v9.5.2 | |||
Single Path (NECSPS) | No | – |
Pure Storage
Vendor (*1) |
Storage Model | Bus Type | Connect Type (*2) |
Support Status | Required ARK (i.e. Multipath ARK) |
Supported LK Version (*4) |
---|---|---|---|---|---|---|
Pure Storage | FA-400 Series | FC | vSphere (RDM) | YES | No Multipath ARK | v9.0 – v9.5.2 |
Multi Path (DMMP) | YES | DMMP ARK | ||||
Single Path | No | – | ||||
ISCSI | Multi Path (DMMP) | No | – | – | ||
Single Path | No | – | ||||
FlashArray//m Series //m10 //m20 //m50 //m70 |
FC | vSphere (RDM) | No | – | v9.0 – v9.5.2 | |
Multi Path (DMMP) | YES | DMMP ARK | ||||
Single Path | No | – | ||||
FlashArray//x Series //x10 //x20 //x50 //x70 |
FC | vSphere (RDM) | No | – | v9.0 – v9.5.2 | |
Multi Path (DMMP) | YES | DMMP ARK | ||||
Single Path | No | – | ||||
FlashArray//x Series //X10R2 //X20R2 //X50R2 //X70R2 //X90R2 |
FC | vSphere (RDM) | No | – | v9.3.2 – v9.5.2 | |
Multi Path (DMMP) | YES | DMMP ARK | ||||
Single Path | No | – | ||||
iSCSI | vSphere (RDM) | No | – | v9.0 – v9.5.2 | ||
Multi Path (DMMP) | YES | DMMP ARK | ||||
Single Path | No | – |
(*1) EMC storage for use
LifeKeeper acquired the E-Lab certification. See the matrix below for the EMC storage support. https://elabnavigator.dell.com/eln/elnhome |
(*2) Connecting Configurations
vSphere (RDM) | Connected a shared disk using Raw Device Mapping (RDM) on the VMWare ESX server |
Multi Path (DMMP) | Multipath configuration of the shared disk using the Device Mapper Multipath driver |
Multi Path (EMPD) | Multipath configuration of the shared disk using the ETERNUS Multipath Driver |
Multi Path (HDLM) | Multipath configuration of the shared disk using the Hitachi Dynamic Link Manager driver |
Multi Path (RDAC) | Multipath configuration of the shared disk using the IBM Redundant Disk Array Controller driver |
Multi Path (NECSPS) | Multipath configuration of the shared disk using the iStorage StoragePathSavior driver |
Single Path (DMMP) | Single path configuration of the shared disk using the Device Mapper Multipath driver |
Single Path (RDAC) | Single path configuration of the shared disk using the IBM Redundant Disk Array Controller |
Single Path | Single path connection not using a specific multipath driver |
(*3) Multipath Software
The support information by maker must be referred about the connectivity information of each Multipath software. Please refer to the release notes for the details about Multipath software support by LifeKeeper. |
(*4) Supported versions of LifeKeeper
This document is written for LifeKeeper for Linux v9. If you are using a previous version of LifeKeeper, you must refer to the Release Notes for that version for the supported storage list. |
Post your comment on this topic.